Eskaro Objekt

Deep matt isolating acrylate paint

Reinforced with synthetic resin
Isolates dirt efficiently
Excellent adhesion to a variety of substrates

Description
Specifications
Information
Certificates

Properties
Acrylate water-borne paint for badly fouled surfaces in rooms with high service load.

Isolates nicotine, smoke, soot and rust stains, water and similar stains well.
Repaints badly fouled surfaces well, providing an absolutely matt dense coating.
Good opacity.
High adhesion to a variety of substrates, including the surfaces painted with alkyd and oil-base paints.
Reinforced with synthetic resin
Is especially suitable for urgent repair works
Can be tinted into over 10,000 colours

Maximum permissible EU VOC content for the product (subcat i) 140 g/L. Maximum VOC content in the product ≤140 g/L.
Gloss:

deep matt (approximately 2) in accordance with EN 13300;
deep matt (approximately 2) in accordance with ISO 2813;

Wash resistance:

class 3 in accordance with EN 13300 (ISO 11998);

Purpose

Intended for repainting badly fouled surfaces in apartment building stairwells, staircases, corridors, hotels, kitchen ceilings.
Suits well as a primer to be used under water-borne paints.

Types of surfaces for painting

Surfaces previously painted with water-borne, alkyd or oil-base paints or new surfaces made of concrete, aerated concrete, gypsum board; brick; surfaces finished with putty or plastered. For indoor use.

Quality standards

EN 13300 [Paints and varnishes. Water-borne coating materials and coating systems for interior walls and ceilings. Classification] – classification standards of coverage, gloss level and wet abrasion resistance parameters for water-borne coating materials for interior walls and ceilings.
ISO 11 998 [Paints and varnishes -- Determination of wet-scrub resistance and cleanability of coatings], ISO 2813 [Paints and varnishes -- Determination of specular gloss of non-metallic paint films at 20 degrees, 60 degrees and 85 degrees] – techniques for measuring gloss and wear resistance parameters.
VOC (volatile organic compounds) – content in accordance with the European Union directive 2004/42/CE.
Product and service quality is guaranteed by the quality, environmental protection, occupational health and safety management system in accordance with standards ISO 9001:2015; ISO 14001:2015 and OHSAS 18001:2007.

Ручная колеровка

by pigment pastes AURA

… Assortment of pastes

Машинная колеровка

База A pastel colours

…

Surface preparation before painting

The surface to be painted must be carefully cleaned from peeling material, dirt and dust. Fill cracks and dents with suitable putty (Fine Filler, Aqua Filler etc.).
We recommend you to wash the surface with a 3–5% solution of soda or a detergent containing ammonia solution, rinse it with water and dry before painting.
The surfaces that get wet so often that mould can develop there must be treated with Biotol E before painting.
The surfaces newly finished with putty should be primed with the Aquastop or Tiefgrund moisture barrier. Follow the product instructions for use.

Application

Stir the paint thoroughly before application. The paint can be diluted with water in the amount of up to 5% of its volume for the application of the first coat. Apply 2 coats with a roller or spray gun at the temperature between
10°C and 25 °C and relative humidity not exceeding 80%. Avoid application in draughty places and at high air temperature (over +25°C). When painting, make sure to keep a wet edge.

Care for the painted surface

The product achieves its final hardness and durability after one month under normal conditions; therefore the surfaces must be handled with care during this time.
If necessary, the surface can be lightly wiped with a soft sponge or cloth approximately 48 hours after paint application. We recommend using water and neutral or medium alkaline detergents (pH below 9). Do not use solvents, abrasive cleansers and hard scrubbing brushes or sponges. Extensive rubbing may make the surface glossy. We recommend using Biotol E and Biotol Spray to remove mould.

Tools

Roller, brush.

Tool cleaning

Wash with soap and water after completing work.

Colour	White.
Tinting	Machine tinting according to the Eskarocolor system (bases А).
Consumption	6-10 m²/L.
Drying time	At the temperature of +20 °C and the relative humidity of 50%, the surface is ready for the application of another coat in 1–1.5 hours and is fully dry in 2 hours.

Store and transport in tightly sealed containers at the temperature between +5 °С and +30 °С. Protect from exposure to freezing and direct sunlight.

Volume / weight

0,9 L – 2,7 L –9L

Warranty period of storage	3 years
Frost resistance	None.
Density